Projects
Projects: Projects for Investigator |
||
| Reference Number | EP/F005296/1 | |
| Title | A New Route to high-Performance Functional Films on Polymeric Web | |
| Status | Completed | |
| Energy Categories | Renewable Energy Sources(Solar Energy, Photovoltaics) 10%; Not Energy Related 90%; |
|
| Research Types | Basic and strategic applied research 100% | |
| Science and Technology Fields | PHYSICAL SCIENCES AND MATHEMATICS (Metallurgy and Materials) 100% | |
| UKERC Cross Cutting Characterisation | Not Cross-cutting 100% | |
| Principal Investigator |
Dr H Assender No email address given Materials University of Oxford |
|
| Award Type | Standard | |
| Funding Source | EPSRC | |
| Start Date | 01 October 2007 | |
| End Date | 31 March 2011 | |
| Duration | 42 months | |
| Total Grant Value | £247,669 | |
| Industrial Sectors | Electronics | |
| Region | South East | |
| Programme | Manufacturing : ICT | |
| Investigators | Principal Investigator | Dr H Assender , Materials, University of Oxford (100.000%) |
| Recognised Researcher | Dr BM Henry , University of Oxford (0.000%) |
|
| Industrial Collaborator | Project Contact , Gencoa Ltd (0.000%) Project Contact , Keeling and Walker Limited (0.000%) Project Contact , Toppan Printing Co (UK) Ltd (0.000%) Project Contact , DuPont Teijin Films UK Limited (0.000%) Project Contact , Kodak European Research (0.000%) Project Contact , Chemfilt Ionsputtering AB, Sweden (0.000%) |
|
| Web Site | ||
| Objectives | ||
| Abstract | Functional films underpin many electronic and opto-electronic devices, including flat panel displays, OLED's, image sensors, thin film photovoltaic solar cells, etc. Of particular importance to these devices are transparent conductive oxide (TCO) films, such as indium tin oxide (ITO) and aluminium-doped zinc oxide (ZAO). The UK market for functional films is expected to rise to 23.4B by 2010. Further substantial gains in productivity would be made, and new markets opened up, if the devices could be deposited directly onto polymeric web in very large throughput reel-to-reel coaters. However, the deposition of TCO films onto webs poses many significant technological challenges. In comparison to glass, polymeric webs are relatively rough, tend to outgas significantly and are thermally sensitive. The latter point particularly poses a problem, because it is generally necessary to perform a post-deposition annealing process (typically at 500 degC) in order to optimise the opticaland electrical properties of TCO materials.One potential solution to this problem is to deposit coatings using the newly developed technique of high powered impulse magnetron sputtering (HIPIMS). This process involves the application of very large power pulses to magnetron sputter cathodes for short periods of time. The peak pulse power can be in the megawatt range and the pulse duration is typically of the order of 80-160 micro seconds, at repetition rates in the range of 10s to 100s of Hz.Initial studies of the HIPIMS (also referred to as high power pulsed magnetron sputtering / HPPMS) system have shown that this intense pulse creates a high degree of ionization (up to 70% for titanium) of the sputtered species with this technique (in contrast to conventional magnetron sputtering, where usually less than 1% of the sputtered material is ionized).The degree of ionization of the sputtered species in HIPIMS is comparable to that produced in cathodic arc discharges; however,with HIPIMS macroparticles are not normally produced. Another important consideration is that, due to the very low duty cycles (~1%) and long off times, the total heat load to the substrate can be very significantly (5-10 times) lower than in conventional DC and pulsed DC sputtering. Thus, the potential for HIPIMS is to harness the high degree of ionization to produce films with significantly improved properties, whilst maintaining a suitably low (sub-150 degC) substratebulk temperature, allowing a diverse range of substrate materials to be coated.The introduction of HIPIMS technology, therefore, has the potential to provide a step-change in the performance of functional films, such as TCO's, deposited onto polymeric webs. This project will offer the first opportunity to study this new, complex deposition process in detail in both a development-scale system at MMU and an industrial pilot scale reel-to-reel coater at Oxford University. An additional keyelement of theproject will be a detailed study of the nature of the discharge. Plasma characteristics such as the spatial and temporal evolution of the concentrations and temperatures of the species and their power loading of the substrate will be determined using an array of time-resolved diagnostic tools and well developed optical imaging techniques.The ability to deposit fully dense TCO coatings with optimised properties onto flexible substrates would be a major breakthrough and would represent a significant advancement in web coating technology | |
| Publications | (none) |
|
| Final Report | (none) |
|
| Added to Database | 04/07/07 | |
