UKERC Energy Data Centre: Projects

Projects: Projects for Investigator
UKERC Home >> UKERC Energy Data Centre >> Projects >> Choose Investigator >> All Projects involving >> EP/M018849/1
 
Reference Number EP/M018849/1
Title Complex Contour Method
Status Completed
Energy Categories FOSSIL FUELS: OIL, GAS and COAL(Oil and Gas, Other oil and gas) 20%;
NUCLEAR FISSION and FUSION(Nuclear Fission, Nuclear supporting technologies) 20%;
OTHER POWER and STORAGE TECHNOLOGIES(Electric power conversion) 20%;
NOT ENERGY RELATED 40%;
Research Types Basic and strategic applied research 100%
Science and Technology Fields PHYSICAL SCIENCES AND MATHEMATICS (Metallurgy and Materials) 100%
UKERC Cross Cutting Characterisation Not Cross-cutting 100%
Principal Investigator Dr F Hosseinzadeh
No email address given
Engineering & Innovation
Open University
Award Type Standard
Funding Source EPSRC
Start Date 01 April 2015
End Date 31 July 2017
Duration 28 months
Total Grant Value £96,748
Industrial Sectors Aerospace; Defence and Marine; Manufacturing
Region East of England
Programme NC : Engineering
 
Investigators Principal Investigator Dr F Hosseinzadeh , Engineering & Innovation, Open University (100.000%)
  Industrial Collaborator Project Contact , Open University (0.000%)
Project Contact , EDF Energy Nuclear Generation Limited (0.000%)
Project Contact , Rolls-Royce PLC (0.000%)
Project Contact , University of California Davis, USA (0.000%)
Web Site
Objectives
Abstract The safe operation of engineering structures is vital in safety-critical industries such as power generation, nuclear, aerospace and oil and gas. Structural failures can have catastrophic consequences in terms of loss of life and financial circumstances. Meanwhile there is a strong interest in reducing costs, light-weighting, increasing design life and life extension. To this end, reliable structural integrity assessments are essential at the design stage and through in-service life to ensure continuous profitable operation of assets.Residual stresses are inevitably introduced in engineering structures during manufacturing processes. Their presence can have adverse effects on the behaviour of structures and contribute to driving force promoting various degradation mechanisms. Therefore, it is of paramount importance that the state of residual stresses in engineering structures is carefully and reliably characterised so that remedial actions could be taken to enhance the lifetime of current materials or novel designs and manufacturing methods developed and optimised.The contour method, first presented in 2000, is emerging as a powerful technique for the measurement of residual stresses in bulky parts. The method involves making a straight cut in the component of interest along a nominally flat plane where residual stresses are desired to be determined. The created cut surfaces deform due to the relaxation of residual stresses. The deformation of the cut surfaces are measured and then used to back-calculate 2D distribution of residual stress that was present along the flat plane prior to the cut.Nevertheless, there are still several limitations associated with application of the contour method: a) only a straight cut over a flat plane is used to section components for contour measurements; b) the standard method can only measure 2D distribution of one component of the residual stress tensor over a flat plane; c) the method is limited to symmetric sectioning of the cut parts, d) like other mechanical strain relief techniques, the contour method is prone to plasticity-induced errors where the magnitude of stresses or level of triaxiality is very high and e) most historical measurements using the contour method have concerned simple geometries such as welded rectilinear plates.For the first time, the "Complex Contour Method" proposes to develop the use of complex cutting paths, for example non-planar and closed complex cutting paths instead of cutting along a flat plane. This innovative approach will radically bring new capabilities for the contour method in several ways: it will unlock map of residual stress in multiple directions simultaneously. Of a true step change is extending the application of the technique to measure 3D maps of residual stress. Enabling the technique to deal with complex cutting paths will inherently deal with limitations of the standard method regarding symmetry of the cut parts. Moreover, removing the constraint ofa symmetric planar cut opens the potential to mitigate plasticity-induced errors that can accompany standard contour method cuts.Of another radical step change of the application of the complex cutting paths is that it enables the technique to be implemented on complex engineering structures. For example, the conventional contour method confined to symmetric planar cuts cannot be applied to complex components such as tube penetration welds for pressure vessel heads.The proposed research has the potential to provide far more complete residual stress information about safety critical components of high interest to engineers in the aerospace, petrochemical, power generation and nuclear industries. In addition for industrial applications, a single complex contour cut offers a far more cost effective tool compared to the cumbersome and time consuming conventional contour method using multiple-method and multiple-cut approaches.
Publications (none)
Final Report (none)
Added to Database 19/06/15